Skip to main content Skip to navigation

Mouse IgE ELISA Protocol

 

Coat with Capture Antibody

 

  1. Shake plate to ensure all wells are covered by capture antibody solution.
  2. Cover the plate and incubate for 1 hour at 37°C or overnight at 4°C.
  3. Wash the plate 3X with PBS/Tween®*. For each wash, wells are filled with 200 µl PBS/Tween ® and allowed to stand at least 1 min prior to aspirating or dumping. As a final step, tap plate on paper towels to remove excess buffer.

 

Blocking

 

  1. Block the plate with 200 µl blocking buffer* per well.
  2. Cover the plate and incubate at RT for 30 min.
  3. Wash the plate 3X with PBS/Tween ®, as in Section I, Step 4, of this protocol.

 

Apply Standards and Samples

 

  1. Leave column 1 as blank wells (i.e., no antigen added, 100 µl per well blocking buffer only). Use columns 2 and 3 for duplicates of the standard, 100 µl per well: dilute purified mouse IgE a standard (cat. no. 557079, clone C38-2; or cat. no. 553481, clone 27-74) or mouse IgE a standard (cat. no. 557080, clone C48-2) in a series of 8 two-fold dilutions, in blocking buffer, starting at 0.5 µg/ml. Use the remaining columns to add samples at various dilutions in blocking buffer, 100 µl per well.
  2. Cover the plate and incubate for at least 1 hour at RT or overnight at 4°C. b
  3. Wash the plate 3X with PBS/Tween®, as in Section I, Step 4, of this protocol.

 

Incubation with Detection Antibody:

 

  1. Dilute biotinylated anti-mouse IgE (cat. no. 553419, clone R35-118) to 2 µg/ml a in blocking buffer. Add 100 µl per well.
  2. Cover the plate and incubate at RT for 1 hour.
  3. Wash the plate 6X with PBS/Tween®, as in Section I, Step 4, of this protocol.

 

Add Streptavidin-Horseradish Peroxidase (SAv-HRP):

 

  1. Dilute Avidin-HRP (cat. no. 554058) or Streptavidin-HRP (cat. no. 554066) 1:1000 in blocking buffer c . Add 100 µl per well.
  2. Cover the plate and incubate at RT for 30 min.
  3. Wash the plate 6X with PBS/Tween® , as in Section I, Step 4, of this protocol.

 

Add Substrate and Develop:

 

  1. Thaw substrate (ABTS) buffer* within 20 min of use. Add 11 µl of 30% H 2 O 2 (Sigma, Cat. No. H1009) to 11 ml substrate buffer and vortex. Immediately add 100 µl per well and allow to develop at RT for 20-30 min. Color reaction can be stopped by adding 50 µl per well of SDS/DMF Solution* (optional).
  2. Read the plate at 405 nm.

 

Solutions:

 

Coating Buffer : PBS, pH 7.2 - 7.4

PBS/Tween ® : PBS pH 7.2-7.4, Tween ® -20, 0.05%

Substrate Buffer :

ABTS (3-ethylbenzthiazoline-6-sulfonic acid, Sigma Cat. No. A-1888), 150 mg
0.1 M citric acid (e.g., Fisher anhydrous, Cat. No. A-940), 500 ml
Adjust pH to 4.35 with NaOH pellets
Aliquot at 11 ml per vial and store at -20°C

SDS/DMF Solution :

40% SDS (80 g SDS in 200 ml dd H 2 O)
Add 200 ml DMF (N.N-dimethyl formamide)

PBS Solution :

NaCl, 80.0 g
Na 2 HPO 4 , 11.6 g
KH 2 PO 4 , 2.0 g
KCl, 2.0 g
Add H 2 O to 10 liter
Adjust pH to 7.2 - 7.4

Blocking Buffer :

PBS, pH to 7.2 - 7.4
10% Fetal calf serum or 1% BSA

 

Notes

 

  1. In most cases, coating the plate with primary mAb at 2 µg/ml, 100 µl per well and detecting with the biotinylated secondary mAb at 2 µg/ml, 100 µl per well yields a very satisfactory signal. However, for optimal signal, researchers should titrate each mAb over a range of concentrations (e.g., 1 - 8 µg/ml).
  2. Recommended incubation times for optimal sensitivity.
  3. Streptavidin/Avidin-HRP conjugate from another supplier may be substituted and diluted according to the manufacturer's recommendation.

 

For troubleshooting information and details on ELISA techniques, please visit the page.