Skip to main content Skip to navigation
Anti-Rat and Anti-Hamster Ig κ /Negative Control Compensation Particles Set

BD™ CompBeads Anti-Rat and Anti-Hamster Ig κ /Negative Control Compensation Particles Set

Clone RG7/7.6

(RUO)
Product Details
Down Arrow Up Arrow


BD™ CompBeads
Flow cytometry (Routinely Tested)
500183
RUO
AB_10058522


Description

The BD™ CompBeads Compensation Particles Anti-Rat/Hamster Ig, κ Set are polystyrene microparticles which are used to optimize fluorescence compensation settings for multicolor flow cytometric analyses. The set provides two populations of microparticles, the BD CompBeads Anti-Rat/Hamster Ig, κ particles, which bind any rat or hamster κ light chain-bearing immunoglobulin, and the BD CompBeads Negative Control (FBS) Particles, which has no binding capacity. When mixed together with a fluorochrome-conjugated rat or hamster antibody, the BD CompBeads provide distinct positive and negative (background fluorescence) stained populations which can be used to set compensation levels manually or using instrument set-up software. Since the compensation adjustments are made using the same fluorochrome-labeled antibody to be used in the experiment, this method allows the investigator to more accurately establish compensation corrections for spectral overlap for any combination of fluorochrome-labeled antibodies (without having to use valuable tissue samples or hard-dyed beads with potentially mismatched fluorescence spectra). Use of the BD CompBeads is highly recommended for use in all experiments using tandem dye (i.e., PE-Cy7, APC-Cy7, etc.) conjugates, which may have distinct spectral characteristics for each conjugate.  

Preparation And Storage

Store undiluted at 4°C and protected from prolonged exposure to light. Do not freeze.

Recommended Assay Procedures

Note:  BD Horizon™ V500 and AmCyan conjugated reagents can show significant differences in emission spectrum on stained cells and when captured on BD™ CompBeads.  Thus, spillover values for these dyes evaluated with BD™ CompBeads may not provide correct compensation for cells.  Therefore, single stained cellular controls are recommended to set up compensation for AmCyan and BD Horizon™ V500 reagents.  BD Horizon™ V500-C has been modified to minimize these spectral differences and BD™ CompBeads may be used to determine spillover values for RUO antibodies conjugated to BD Horizon™ V500-C.

Without affecting compensation function, some lots may profile as a bi-modal histogram, which may be possible due to inherent light scatter and/or residual aggregation of the compensation particles.  Optimization of instrument voltage or gating conditions may be helpful for improving histogram visualization.

This BD™ CompBeads Set has been tested with hamster Ig antibodies conjugated to various fluorochromes and analyzed using a BD FACS brand flow cytometer to ensure specificity and reactivity of the particles.  See the specific instructions below on the use of the BD™ CompBeads Set:

1.   Vortex BD™ CompBeads thoroughly before use.

2.   Label a separate 12 x 75 mm sample tube for each flurochrome-conjugated mouse Ig, κ antibody to be used on a given experiment.

3.   Add 100 µl of staining buffer [eg, BD Pharmingen Stain (FBS), Cat. No. 554656 or BD Pharmingen Stain (BSA), Cat. No. 554657] to each tube.

4.   Add 1 full drop (approximately 60 µl) of the BD CompBead Negative Control (FBS) and 1 drop of the BD™ CompBead Anti-Rat/Hamster Ig, κ beads to each tube and vortex.

5.   Add 20 µl of each prediluted antibody stock (diluted to a concentration optimal for staining 10^6 cells) to be tested on a given experiment to the appropriately-labeled tube. (Make sure the antibody is deposited to the bead mixture, then vortex.)

6.   Incubate 15 - 30 minutes at room temperature. Protect from exposure to direct light.

7.   During the incubation of beads and antibody, set the flow cytometer instrument PMT voltage settings using the target tissue for the given experiment (eg, whole blood, splenocytes, etc.). If you are unsure, use the BD CompBeads Negative Control (FBS*) beads as your negative reference point and proceed.

8.   Following the incubation step (see Step 6 above), add 2 ml staining buffer to each tube and pellet by centrifugation at 200 x g for 10 minutes.

9.   Discard supernatant from each tube by careful vacuum aspiration using a fine-tip Pasteur pipette.

10. Resuspend bead pellet in each tube by adding 0.5 ml of staining buffer to each tube. Vortex thoroughly.

11. Run each tube separately on the flow cytometer. Gate on the singlet bead population based on FSC (forward-light scatter) and SSC (sidelight scatter) characteristics.

12. Adjust flow rate to 200 - 300 events per second if possible.

13. Create a dot plot for the given fluorochrome-conjugated antibody as appropriate [i.e., to set compensation for a fluorescein (FITC)-conjugated antibody, use an FL1 vs. FL2 dot plot].

14. Place a quadrant gate such that the negative bead population is in the lower left quadrant and the positive bead population is in the upper or lower right quadrant, and adjust the compensation values until the median fluorescence intensity (MFI) of each population (as shown in the quadrant stats window) is approximately equal (i.e., for FL2 -%FL1, the FL2 MFI of both bead populations should be approximately equal when properly compensated).

15. Repeat Steps 13 and 14 for other tubes, as necessary.

16. Proceed to acquiring the actual staining experiment.

Product Notices

  1. Cy is a trademark of Amersham Biosciences Limited.
  2. Although hamster immunoglobulin isotypes have not been well defined, BD Biosciences Pharmingen has grouped Armenian and Syrian hamster IgG monoclonal antibodies according to their reactivity with a panel of mouse anti-hamster IgG mAbs. A table of the hamster IgG groups, Reactivity of Mouse Anti-Hamster Ig mAbs, may be viewed at http://www.bdbiosciences.com/documents/hamster_chart_11x17.pdf.
  3. Source of all serum proteins is from USDA inspected abattoirs located in the United States.
  4. Caution: Sodium azide yields highly toxic hydrazoic acid under acidic conditions. Dilute azide compounds in running water before discarding to avoid accumulation of potentially explosive deposits in plumbing.
  5. Please refer to www.bdbiosciences.com/us/s/resources for technical protocols.
552845 Rev. 6
Components
Down Arrow Up Arrow
Description Quantity/Size Part Number EntrezGene ID
Anti-Rat and Anti-Hamster Ig, κ 6 mL (1 ea) 51-90-9000949 500183
Negative Control 6 mL (1 ea) 51-90-9001291 500183
552845 Rev. 6

Please refer to Support Documents for Quality Certificates

Global - Refer to manufacturer's instructions for use and related User Manuals and Technical data sheets before using this products as described

Comparisons, where applicable, are made against older BD Technology, manual methods or are general performance claims.  Comparisons are not made against non-BD technologies, unless otherwise noted.

For Research Use Only. Not for use in diagnostic or therapeutic procedures.

Refer to manufacturer's instructions for use and related User Manuals and Technical Data Sheets before using this product as described.

Comparisons, where applicable, are made against older BD technology, manual methods or are general performance claims. Comparisons are not made against non-BD technologies, unless otherwise noted.